Vetroo Eclipse 90mm Low-Profile ARGB Review (2026): A Spec-Based Look
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This vetroo eclipse 90mm low profile argb CPU cooler review focuses on a compact cooling solution designed for small form factor builds. The unit features a 90mm fan and stands at just 72mm tall. It supports only Intel LGA 1700 and LGA 1851 sockets. The fan speed ranges from 800 to 2500 RPM with PWM control. ARGB lighting syncs via a 5V 3-pin header. This design prioritizes case compatibility and direct airflow over the CPU. You get a low-profile tower that fits tight spaces without sacrificing basic thermal performance.
What stands out
- 72mm height fits small PC cases
- 90mm fan with 800-2500 RPM range
- Supports Intel LGA 1700 and 1851
- 5V 3-pin ARGB dual ring lighting
- Top-to-bottom airflow design
Who it fits
Good fit for
You should consider this cooler if you are building a compact PC with an Intel LGA 1700 or 1851 processor. The 72mm height makes it ideal for small form factor cases where space is limited. The PWM fan allows you to balance noise and airflow. The ARGB lighting adds visual appeal if you want synchronized effects. It is a practical choice for users who need a low-profile solution that still offers dynamic speed control and specific socket support.
Who should skip it
You should look elsewhere if you use an AMD platform or older Intel sockets. This cooler only supports LGA 1700 and LGA 1851. The 90mm fan size provides less cooling capacity than larger 120mm or 140mm units. If you need high-end thermal performance for overclocking, this low-profile design may not be sufficient. Additionally, if you prefer 12V ARGB lighting, this model uses a 5V 3-pin interface, which may not be compatible with your motherboard.
Verdict: This cooler is a spec-driven option for small Intel-based builds. It fits tight spaces but limits socket choice and cooling power.
Key specs explained for Vetroo Eclipse
Fan Size: 90mm
The fan diameter is 90 millimeters, which is smaller than the standard 120mm or 140mm fans found in most towers. Smaller fans require higher RPMs to move the same air volume. You should check if your case has enough clearance for this size. It suits compact builds where space is tight. Compare it with larger fans if you need maximum airflow in a spacious chassis.
Cooler Height: 72mm
The total height of the cooler is 72 millimeters. This low-profile design allows it to fit inside small form factor cases that cannot accommodate tall towers. You must verify your case supports coolers under 80mm. This spec is critical for ITX builds. Compare it with standard 150mm coolers, which offer more cooling power but require much more vertical clearance inside your computer case.
Fan Speed: 800-2500±10% RPM
The fan operates between 800 and 2500 revolutions per minute with a ten percent tolerance. The PWM control lets you adjust speed dynamically. Lower speeds mean less noise, while higher speeds provide more cooling. You can tune this based on your thermal needs. Compare this range with other air coolers to see if the maximum speed meets your cooling demands for high-end processors.
Socket Compatibility: LGA 1851, LGA 1700
This cooler supports only Intel LGA 1851 and LGA 1700 sockets. It does not fit AMD or older Intel platforms. You must ensure your motherboard uses one of these specific socket types before purchasing. This limitation restricts upgrade paths for some users. Compare this with universal coolers that support multiple sockets if you plan to change your CPU platform in the future.
Design and Build Details
According to the listing, this cooler features a low-profile tower design with a compact footprint. The overall dimensions are 3.94 inches in width, 3.94 inches in length, and 2.83 inches in depth. The cooler height is listed at 72mm. This small size makes it suitable for tight spaces in small form factor PC builds. You need to ensure your case can accommodate this height before purchasing.
The unit uses a 90mm fan to move air. The airflow direction is top-to-bottom. This layout cools the CPU first and then helps cool surrounding motherboard hardware. The fan speed is adjustable via PWM control. It runs between 800 and 2500 RPM, with a variance of plus or minus 10 percent. This range lets you choose between maximum airflow or lower noise levels.
Lighting is provided by an ARGB dual ring effect. You can sync this lighting with your motherboard using a 5V 3-pin interface. This allows the cooler to match the rest of your build’s aesthetic. The listing specifies support for Intel LGA 1851 and LGA 1700 sockets only. Other sockets are not supported. This restriction means you must verify your motherboard compatibility. The design prioritizes fit and airflow in constrained cases rather than universal socket support.
Setup And Daily Use
Installation requires careful planning because this cooler only supports Intel LGA 1700 and LGA 1851 sockets. You cannot mount it on AMD platforms or older Intel generations. The low-profile tower stands at 72mm tall. This height allows it to fit inside small form factor cases where standard coolers are too large. You must verify your case clearance before purchase. The compact dimensions of 3.94 inches by 3.94 inches keep the footprint small. This design prioritizes space efficiency over raw cooling capacity.
Daily operation relies on the included 90mm fan. The fan speed adjusts dynamically between 800 and 2500 RPM via a 4-pin PWM connection. This range lets you balance noise levels against airflow. Lower speeds reduce sound, while higher speeds increase air movement. The top-to-bottom airflow design directs air from the fan across the fins and down toward the motherboard. This path cools the CPU first, then helps dissipate heat from surrounding components. The airflow pattern is fixed by the physical orientation of the fan and heatsink.
Lighting is handled by dual ARGB rings. These rings connect to a 5V 3-pin header on your motherboard. This interface allows the lighting to sync with other compatible components in your build. The visual effect is purely aesthetic and does not impact cooling performance. You configure the lighting through your motherboard software. The unit operates silently at idle speeds and may become audible under heavy load due to the higher RPM requirement of the smaller fan.
Before You Buy This Cooler
This cooler is a specialized tool for small form factor builds. You must verify your case supports a 72mm height limit before purchasing. The listing confirms it only works with Intel LGA 1700 and LGA 1851 sockets. You cannot install this on AMD platforms or older Intel generations. Check your RAM clearance, as the 90mm fan sits close to memory slots. You need a motherboard with a 5V 3-pin ARGB header to sync the dual ring lighting. If your board lacks this port, the lights will not function. The PWM fan allows speed control between 800 and 2500 RPM. This range lets you balance noise and airflow. Keep the fins clean to maintain performance. This option suits users prioritizing compactness over raw cooling power. It sits alongside larger towers as a niche choice for tight spaces. Always confirm your specific case dimensions and socket type match the listed specs.
Check before you buy
- Verify your PC case supports a 72mm cooler height limit.
- Confirm your motherboard uses Intel LGA 1700 or LGA 1851 sockets.
- Check for a 5V 3-pin ARGB header on your motherboard.
- Measure RAM height clearance near the CPU socket area.
The product at a glance
Vetroo Eclipse 90mm Low-Profile ARGB Cooler
Best for: small Intel LGA 1700/1851 builds
- Socket Compatibility
- Intel LGA 1851 & 1700
- Cooler Height
- 72mm
- Tower Design
- Low-Profile
- Fan Size
- 90mm
- TDP Rating
- 95W
- Fan Speed
- 2500±10% RPM
View on Amazon: Vetroo Eclipse 90mm Low-Profile ARGB Cooler Affiliate link
The Vetroo Eclipse is a low-profile air cooler designed for small form factor builds. It features a 72mm height and a 90mm fan. The cooler supports Intel LGA 1700 and LGA 1851 sockets. It includes ARGB lighting that syncs via a 5V 3-pin interface. The fan speed ranges from 800 to 2500 RPM for adjustable airflow. This unit suits users needing compact cooling for specific Intel platforms.
Pros
- 72mm height fits small cases
- 90mm fan with PWM control
- ARGB dual ring lighting
- Supports LGA 1700 and 1851
Cons
- Limited to Intel LGA 1700 and 1851 sockets
- 90mm fan size offers less surface area than standard 120mm models
- Only supports 5V 3-pin ARGB synchronization
Good fit if
- You are building in a small form factor case
- You use an Intel LGA 1700 or 1851 motherboard
- You want ARGB lighting in a low-profile design
Skip if
- You need compatibility with AMD sockets
- You require a standard 120mm or larger fan size
- You use a motherboard with only 4-pin ARGB headers
Verdict: Vetroo Eclipse 90mm Low-Profile ARGB is a compact cooling solution for Intel LGA 1700 and 1851 builds. It fits small cases and provides adjustable fan speeds with lighting effects.
Specifications side by side
| Spec | Vetroo Eclipse 90mm Low-Profile ARGB Cooler |
|---|---|
| Socket Compatibility | Intel LGA 1851 & 1700 |
| Cooler Height | 72mm |
| Tower Design | Low-Profile |
| Fan Size | 90mm |
| TDP Rating | 95W |
| Fan Speed | 2500±10% RPM |
| Lighting | ARGB |
| Material | Aluminum |
| Features | Fan |
| Dimensions | 3.94 × 3.94 × 2.83 inches |
| Model | NL-CPU-ECLIPSE |
Frequently asked questions
Does the Vetroo Eclipse 90mm fit AMD motherboards?
No, this cooler is designed exclusively for Intel platforms. The product data confirms it supports only LGA 1700 and LGA 1851 sockets. You cannot mount it on AMD Ryzen systems or older Intel generations. If you need a cooler for AMD, you must look for a different model that lists compatible AM4 or AM5 sockets.
What is the maximum height of this CPU cooler?
The Vetroo Eclipse 90mm has a maximum height of 2.83 inches. This dimension is equivalent to 72 millimeters. This low profile allows it to fit inside compact cases that have strict clearance limits. You should measure your case interior to ensure it accommodates this height before purchasing.
Does this cooler include RGB lighting?
Yes, the Vetroo Eclipse 90mm features ARGB lighting. The product attributes list ARGB as its lighting type. This allows you to synchronize the fan colors with other compatible components in your build. You will need an ARGB header on your motherboard to control the effects.
What is the width of the Vetroo Eclipse cooler?
The width of this cooler is 3.94 inches. The listing specifies the width and length as identical measurements. This square footprint helps it fit into small form factor cases with limited lateral space. You should verify that your case interior has enough width to accommodate these dimensions.
Is the Vetroo Eclipse suitable for small ITX builds?
Yes, this cooler is ideal for small Intel LGA 1700 or LGA 1851 builds. Its compact dimensions and low-profile design make it suitable for tight spaces. The 90mm fan size reduces overall bulk compared to standard towers. It is a practical choice for users prioritizing case compatibility over maximum cooling potential.
What is the model number for this Vetroo cooler?
The model number for this unit is NL-CPU-ECLIPSE. This identifier helps you find the correct mounting hardware and drivers online. It distinguishes this specific 90mm low-profile ARGB version from other products in the Vetroo lineup. You can use this number when searching for installation guides or support resources.