Dynatron Copper LGA1156 Blower Heatsink Review: Specs, Pros and Cons
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This dynatron k199 socket lga1156 copper review covers a dedicated cooling solution for older Intel platforms. The unit features a solid copper heat sink designed to transfer heat efficiently from the processor. It includes a 3-inch blower fan that directs airflow over the fins. The fan connects via a 4-pin DC12V interface, allowing for standard PWM control. With dimensions of 3.35 by 3.21 by 1.12 inches, it fits within specific case constraints. This is a straightforward, spec-driven cooler for legacy systems.
What stands out
- Copper heat sink material for direct thermal contact
- 3-inch blower fan with 4-pin connector
- Compatible exclusively with LGA1156 socket CPUs
- Rated speed of 2600 RPM at 50% duty cycle
- Airflow of 3.533 CFM at low duty cycles
Who it fits
Good fit for
You should consider this cooler if you are maintaining an older desktop with an Intel i5 or i7 processor on an LGA1156 motherboard. The copper construction helps manage heat in systems that lack modern thermal efficiency. The blower design is useful in cases where standard tower coolers do not fit or where you need directed airflow toward the rear exhaust. It is a practical replacement for failed stock coolers on these specific legacy platforms.
Who should skip it
You should look elsewhere if you need support for newer sockets like LGA1700 or AM5. This unit is physically limited to LGA1156, so it will not fit modern motherboards. The small 3-inch fan and limited copper mass restrict performance for high-end or overclocked CPUs. If you require quiet operation or high airflow for a powerful processor, this small blower design will likely struggle to keep temperatures low under heavy load.
Verdict: This is a niche cooler built strictly for LGA1156 systems. It offers basic cooling for older i5 and i7 CPUs using a copper base and small blower fan.
Key specs explained
Material: Copper
Copper has high thermal conductivity, meaning it moves heat away from the CPU core quickly. This material choice helps maintain lower temperatures under load. You benefit from faster heat dissipation compared to aluminum-only designs. When shopping, look for copper base plates for better performance in tight spaces.
Fan Size: 3-inch
A 3-inch fan is significantly smaller than standard 120mm or 140mm case fans. This compact size fits in small form factor cases or older chassis with limited clearance. The smaller diameter may require higher RPMs to move the same air volume, potentially increasing noise levels during operation.
Socket Compatibility: LGA1156
This heatsink is built exclusively for Intel LGA1156 motherboards. It will not fit modern LGA1700 or AM5 sockets. You need this specific compatibility for older Intel Core i5 and i7 processors. Check your motherboard manual to confirm the socket type before purchasing to ensure proper mounting.
Dimensions: 3.35 x 3.21 x 1.12 inches
These physical measurements define the footprint and height of the cooler. The low profile allows it to fit near RAM slots or in cramped cases. Verify that your case supports this height and that nearby components will not obstruct the fan. Smaller dimensions limit total cooling surface area.
Design and build details
The Dynatron K199 heatsink uses a solid copper construction for its thermal base. According to the listing, this material choice prioritizes direct heat transfer from the CPU surface. Copper conducts heat faster than aluminum, which helps move thermal energy away from the processor core efficiently. This design is specific to the LGA1156 socket, ensuring a precise fit for older Intel i5 and i7 processors. You should verify your motherboard socket type before considering this unit, as it is not compatible with modern platforms.
The physical dimensions are compact, measuring 3.35 inches in length, 3.21 inches in width, and 1.12 inches in height. It weighs 12.5 ounces, a moderate mass that helps stabilize the thermal connection without adding excessive strain to the motherboard. The attached 3-inch blower fan is mounted directly to the heatsink. This blower style directs airflow through the fins and exhausts it toward the rear of the case. This layout is useful for small form factor cases or systems with limited airflow paths, as it does not rely on large case fans to push air through the fins.
The fan connects via a 4-pin PWM connector. It operates at 12V and draws 1.20A. The listing notes variable speeds based on duty cycle, ranging from 500 RPM to 2600 RPM. This allows the system to adjust cooling performance based on thermal load. The double ball bearing mechanism suggests a focus on durability over time, though the low airflow ratings indicate it is best suited for low-power CPUs in constrained spaces.
Setup and everyday use
Installing this cooler requires matching the LGA1156 socket. The unit is designed specifically for Intel i5 and i7 CPUs using that platform. You will need to ensure your motherboard supports this older socket type. The heatsink dimensions are 3.35 by 3.21 by 1.12 inches. This compact size fits into standard cases without blocking nearby slots. The 3-inch blower fan attaches directly to the copper block. It uses a 4-pin connector for power. This allows you to control fan speed via your motherboard headers if PWM is supported. The fan operates on 12V DC. At low duty cycles, it runs at 1200 RPM with 3.533 CFM airflow. At full speed, the RPM drops to 500, which seems unusual but is listed as a specification. The double ball bearing design suggests durability over time. In daily use, the blower style pushes air out of the case rather than just over the CPU. This helps cool surrounding components like VRMs. The copper material ensures heat moves from the processor into the fins quickly. You do not need to worry about complex pump setups or liquid loops. It is a simple, direct air cooling solution. The 12.5-ounce weight is light enough for standard mounting brackets. Just verify your case has enough clearance for the 1.12-inch height. The setup is straightforward for anyone familiar with basic PC hardware assembly.
Before You Buy This Cooler
Before you buy this Dynatron K199, verify your motherboard supports the LGA1156 socket. This cooler is designed specifically for Intel i5 and i7 processors from that era. It will not fit modern AM4 or LGA1700 boards. You must ensure your case has enough clearance for the 3.35 by 3.21 by 1.12-inch dimensions. The 3-inch blower fan requires a 4-pin connector on your motherboard. Check that your system provides 12V power to the fan header. This unit is a niche solution for legacy systems. It does not compete with current high-performance air coolers for new CPUs. You should use it only if you are maintaining an older desktop. Regularly clean the copper fins to maintain airflow. Dust buildup reduces the blower’s effectiveness over time. This cooler fits alongside other specialized options in the CPU Air Coolers & Thermal Paste guide. It is not for general-purpose gaming rigs. It is strictly for specific, older Intel platforms. Ensure your power supply can handle the fan’s draw without strain.
Check before you buy
- Verify your motherboard has an LGA1156 socket.
- Confirm your CPU is an Intel i5 or i7.
- Check your case fits the 3.35-inch length.
- Ensure a 4-pin fan header is available.
- Check that your PSU provides stable 12V power.
The product at a glance
Dynatron Copper LGA1156 Blower Heatsink
Best for: LGA1156 systems needing compact copper cooling
- Socket Compatibility
- LGA1156
- Material
- Copper
- Compatible Device
- Intel i5 & i7 CPUs
- Fan Size
- 3-inch
- Dimensions
- 3.35 x 3.21 x 1.12 inches
- Features
- Fan
View on Amazon: Dynatron Copper LGA1156 Blower Heatsink Affiliate link
This Dynatron K199 is a compact copper heatsink designed specifically for LGA1156 sockets, supporting Intel i5 and i7 processors. It features a 3-inch blower fan with a 4-pin connector, rated for 12V operation. The unit measures 3.35 by 3.21 by 1.12 inches and weighs 12.5 ounces. Its small footprint makes it suitable for tight cases, while the copper construction aids in heat dissipation for older Intel platforms.
Pros
- Copper heat sink material for efficient thermal transfer
- Compact dimensions of 3.35 x 3.21 x 1.12 inches
- 4-pin connector supports PWM fan control
- Double ball bearing fan for durability
Cons
- Limited to LGA1156 socket only
- Small 3-inch fan size restricts airflow potential
- Blower design may not vent heat as effectively as tower coolers
Good fit if
- You are upgrading an older LGA1156 system
- You need a low-profile cooler for a small form factor case
- You prefer copper construction for thermal performance
Skip if
- You use a modern socket like LGA1700 or AM5
- You require high airflow for overclocking
- You need a cooler compatible with tall RAM modules
Verdict: Dynatron K199 3-Inch Copper LGA1156 Cooler is a specialized solution for LGA1156 users needing a compact, copper-based cooling option. It fits well in tight cases but lacks the versatility for modern platforms.
Specifications side by side
| Spec | Dynatron Copper LGA1156 Blower Heatsink |
|---|---|
| Socket Compatibility | LGA1156 |
| Material | Copper |
| Compatible Device | Intel i5 & i7 CPUs |
| Fan Size | 3-inch |
| Dimensions | 3.35 x 3.21 x 1.12 inches |
| Features | Fan |
| Weight | 12.5 ounces |
| Model | K199 |
Frequently asked questions
Does the Dynatron K199 support modern LGA1700 sockets?
No, this cooler is strictly for LGA 1156 motherboards. It will not fit current Intel platforms like LGA1700 or AMD AM4. You must verify your motherboard uses the older LGA 1156 socket before purchasing. This unit is designed specifically for legacy Intel i5 and i7 processors from that generation.
What are the physical dimensions of the Dynatron K199?
The heatsink measures 3.35 inches in length, 3.21 inches in width, and 1.12 inches in height. These compact dimensions make it suitable for smaller cases with limited clearance. The total weight is 12.5 ounces. You should check your case specifications to ensure it can accommodate this specific footprint and height.
Is the Dynatron K199 made of copper or aluminum?
It is made of copper. Copper offers higher thermal conductivity than aluminum, allowing it to pull heat away from the CPU core more rapidly. This material choice helps maintain lower temperatures under load. The listing confirms the construction material is copper, prioritizing direct heat transfer efficiency over cost-saving aluminum designs.
Does the Dynatron K199 include a fan?
Yes, it includes a 3-inch blower fan. This fan directs airflow over the copper fins to dissipate heat. The blower design pushes air out of the case rather than just circulating it internally. You benefit from active cooling that relies on this single included fan for operation.
Which CPUs are compatible with the Dynatron K199?
It is compatible with Intel Core i5 and i7 processors that use the LGA 1156 socket. This includes older generation CPUs from the late 2000s and early 2010s. You must ensure your specific processor model uses this socket type. It is not suitable for modern desktop or laptop CPUs.
Is the Dynatron K199 a good choice for tight cases?
Yes, its compact size makes it ideal for tight spaces. The height is only 1.12 inches, which fits many low-profile or small form factor cases. The 3.21-inch width also helps in constrained environments. You gain a specialized cooling solution that prioritizes fitment in smaller builds over high-end performance metrics.