ID-COOLING Dual 120mm Fan 5-Heatpipe Review (2026): A Spec-Based Look
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This id cooling se 225 xt black CPU air review focuses on the ID-COOLING Dual 120mm Fan 5-Heatpipe Cooler. It is a compact air cooler designed for efficient thermal management. The two defining specifications are its five direct contact heat pipes and dual 120mm PWM fans. These fans operate in a push-pull configuration to maximize airflow through the heatsink. The unit measures 4.25 by 5 by 5.9 inches. This size allows it to fit into various chassis without blocking RAM slots. The black finish matches modern builds. The specs suggest a focus on steady heat dissipation for mainstream processors.
What stands out
- Five direct contact heat pipes for efficient heat transfer
- Dual 120mm PWM fans in push-pull configuration
- Maximum airflow of 76.16 CFM
- Noise level between 15.2 and 35.2 dB(A)
- Non-interference with memory mounting on mini-ITX boards
Who it fits
Good fit for
This cooler suits users with Intel LGA1700, LGA1200, or AMD AM4/AM5 sockets who need reliable cooling without excessive noise. The push-pull fan setup helps dissipate heat more efficiently than single-fan designs. Its low profile ensures compatibility with mini-ITX motherboards where RAM clearance is tight. If you prioritize quiet operation with automatic speed control, the PWM fans adjust to your workload. This makes it a practical choice for office PCs or home theater builds.
Who should skip it
You should look elsewhere if you need extreme overclocking headroom. The dual 120mm fans and five heat pipes are designed for standard thermal loads, not high-end enthusiast chips. The noise level can reach 35.2 dB(A) under full load, which may be noticeable in silent builds. Additionally, the 4.25-inch width might interfere with wide RAM heatsinks on some motherboards, despite the non-interference claim for mini-ITX. If you require a larger cooler for better thermals, this unit may fall short.
Verdict: The ID-COOLING SE-225-XT Black offers solid mid-range cooling performance through its dual fan and five heat pipe design. It is a sensible choice for standard builds that value RAM compatibility and quiet operation.
Key specs explained for this cooler
Fan Size: 120mm
This refers to the diameter of the cooling fans. A 120mm size is the standard for modern air coolers, offering a balance between airflow and noise. You get sufficient surface area to move air without requiring excessive speed. This size fits most cases. When shopping, compare this to 140mm fans for slightly better efficiency or 92mm fans for smaller spaces.
Heat Pipes: 5
The cooler uses five copper heat pipes to transfer heat from the CPU base to the aluminum fins. More pipes generally mean better heat spreading and dissipation capacity. This configuration helps maintain lower temperatures under load. When comparing air coolers, check if the competitor uses four or six pipes to gauge relative thermal performance for your specific processor.
Max. Air Flow: 76.16CFM
This specification indicates the maximum volume of air the fans can move per minute. Higher cubic feet per minute (CFM) values suggest stronger cooling potential. You benefit from this when running demanding tasks that generate significant heat. Compare this figure with other models to understand which cooler moves more air, keeping in mind that airflow must be balanced with noise levels.
Noise Level: 15.2-35.2dB(A)
This range shows the sound output of the fans at different speeds. The lower end represents quiet operation, while the higher end indicates maximum fan speed. You can expect whisper-quiet performance at idle and louder operation under heavy load. When selecting a cooler, compare these decibel ratings to find a model that matches your tolerance for background noise during intense computing sessions.
Design and Build Overview
According to the listing, this cooler measures 4.25 inches in width, 5 inches in length, and 5.9 inches in height. These dimensions define its physical footprint on your motherboard. The compact width ensures it avoids interference with memory modules. You can install it even on mini-ITX boards without blocking RAM slots. The height allows it to fit inside most standard mid-tower cases. You should verify your case clearance before purchase. The black finish matches common aesthetic themes. This color choice is purely visual and does not affect cooling performance.
The build centers on five direct contact heat pipes. This layout places the pipes in direct contact with the CPU surface. That design choice aims to transfer heat away from the processor more efficiently than traditional methods. The cooler uses two 120mm fans arranged in a push-pull configuration. This setup forces air through the fins from both sides. The listing states this increases airflow transport into the heatsink. The result is better heat dissipation compared to single-fan designs. The fans are PWM controlled. This means their speed adjusts automatically. You get variable noise levels ranging from 15.2 to 35.2 decibels. The airflow maxes out at 76.16 CFM. These specs suggest a balance between quiet operation and cooling power. The overall design prioritizes compatibility and efficient thermal transfer over flashy aesthetics.
Setup and Everyday Use
Installing this cooler requires mounting it to your motherboard. The listing confirms support for most Intel and AMD sockets. This includes Intel LGA1700, 1200, 115x, 2011, and 2066. It also supports AMD AM4 and AM5. You should verify your specific socket before beginning. The design avoids interference with memory modules. This feature is useful for mini-ITX builds or systems with tall RAM sticks. You do not need to worry about clearance issues between the cooler and your memory slots.
Once installed, the dual 120mm PWM fans operate based on your system’s settings. PWM allows for automatic speed control. This means the fans adjust their rotation speed according to CPU temperature. The listing specifies a maximum air flow of 76.16 CFM. This volume of air moves heat away from the five direct contact heat pipes. The heat pipes transfer thermal energy from the CPU to the aluminum fins efficiently.
During daily use, the push-pull configuration of the fans helps dissipate heat. One fan pushes air into the heatsink, while the other pulls it through. This setup aims to improve cooling efficiency compared to standard single-fan setups. Noise levels range from 15.2 to 35.2 dB(A). At lower speeds, operation remains quiet. At higher loads, the fans spin faster to maintain temperatures. The black finish matches most modern PC cases. The entire assembly relies on these mechanical and electrical specs to function. No software or additional tools are mentioned for daily operation.
Before You Buy This Cooler
Before you install this ID-COOLING cooler, verify your motherboard socket. The listing supports Intel LGA1700, 1200, 115x, 2011, 2066, and AMD AM4, AM5. Ensure your case has enough depth for the 5.9-inch height. Check that your RAM slots are not too close to the cooler base. The dual 120mm fans use PWM, so your motherboard must support fan headers for speed control. You will need thermal paste. The listing does not mention included paste, so buy a tube separately. Clean the old paste from your CPU before applying new paste. This model fits well in compact builds due to its narrow width. It sits alongside other air coolers in our 1 guide. It offers strong airflow for its size. Compare its noise levels and dimensions with other options to find the best fit for your specific case and CPU.
Check before you buy
- Verify motherboard socket compatibility for Intel and AMD.
- Check case dimensions for 5.9-inch height clearance.
- Ensure RAM does not block the cooler base.
- Confirm motherboard has PWM fan headers.
The product at a glance
ID-COOLING Dual 120mm Fan 5-Heatpipe Cooler
Best for: RAM clearance and quiet cooling
- Socket Compatibility
- Intel LGA1700/115X/1200 & AMD AM4/AM5
- Heat Pipes
- 5
- Fan Size
- 120mm
- TDP Rating
- 220W
- System Type
- Desktop
- Color
- Black
View on Amazon: ID-COOLING Dual 120mm Fan 5-Heatpipe Cooler Affiliate link
This air cooler uses five direct-contact heat pipes and dual 120mm PWM fans to move heat away from your CPU. The fans operate between 15.2 and 35.2 dB(A) with a max airflow of 76.16 CFM. Its 4.25-inch width helps it fit with most RAM sticks. It supports Intel LGA1700 and AMD AM5 sockets. You get a compact, black unit that balances cooling performance with low noise levels.
Pros
- Five direct contact heat pipes for efficient heat transfer
- Dual 120mm PWM fans provide up to 76.16 CFM airflow
- Low noise operation starting at 15.2 dB(A)
- Non-interfering design allows for easy RAM installation
Cons
- Limited to dual 120mm fans instead of larger 140mm options
- Max noise level reaches 35.2 dB(A) under full load
- No RGB lighting or software control mentioned in specifications
Good fit if
- You need a cooler that fits with tall RAM modules
- You want quiet operation at low fan speeds
- You are building on Intel LGA1700 or AMD AM5
Skip if
- You require RGB lighting synchronization
- You need software-based fan curve control
- You prefer 140mm fans for maximum airflow
Verdict: ID-COOLING SE-225-XT Black 5-Heatpipe Cooler fits users who prioritize RAM clearance and quiet operation over flashy aesthetics. It delivers solid cooling for mainstream CPUs without blocking memory slots.
Specifications side by side
| Spec | ID-COOLING Dual 120mm Fan 5-Heatpipe Cooler |
|---|---|
| Socket Compatibility | Intel LGA1700/115X/1200 & AMD AM4/AM5 |
| Heat Pipes | 5 |
| Fan Size | 120mm |
| TDP Rating | 220W |
| System Type | Desktop |
| Color | Black |
| Dimensions | 5 × 4.25 × 5.9 inches |
Frequently asked questions
Does the ID-COOLING SE-225-XT Black block RAM slots?
No, it is designed to avoid memory interference. The cooler has a compact width of 4.25 inches. This narrow profile ensures it stays clear of tall memory modules. You can install high-profile RAM without removing the cooler. This makes it suitable for builds where space is tight.
What sockets does this cooler support?
It supports most modern Intel and AMD platforms. For Intel, it fits LGA1700, 1200, 115x, 2011, and 2066. For AMD, it works with AM4 and AM5 sockets. You should verify your specific motherboard socket before purchasing. This wide compatibility covers the majority of current desktop processors.
How tall is the ID-COOLING SE-225-XT Black?
The unit measures 5.9 inches in height. You must check your case specifications to ensure it fits. The total height includes the fans and the heatsink. If your case has a low clearance limit, this cooler might not fit. Always measure the available space above the CPU socket.
What is the color of this cooler?
The model is finished in black. The listing identifies it as the SE-225-XT BLACK. This color matches many modern case interiors and motherboard aesthetics. It does not feature RGB lighting or colorful accents. The design is understated and focuses on function rather than flashy visuals.
Is the fan size 120mm?
Yes, it uses 120mm fans. This is the standard size for many air coolers. The 120mm diameter provides a good balance of airflow and noise levels. You get sufficient surface area to move air efficiently. This size is common and ensures replacement fans are easy to find if needed.
How many heat pipes does it have?
It features five heat pipes. These pipes help transfer heat from the CPU base to the fins. The direct contact design improves thermal conductivity. Five pipes provide adequate surface area for mainstream cooling tasks. This setup helps maintain stable temperatures under typical loads.
Is this cooler good for quiet operation?
It is a good choice for quiet builds. The listing highlights quiet cooling as a key benefit. The 120mm fans can run at lower speeds while moving enough air. This reduces noise compared to smaller fans. You get efficient cooling without the high pitch of smaller, faster-spinning units.